VAPOUR BLASTING, EXPLAINED

How Vapour Blasting Works

Understand the air. Control the finish.

Pressure, airflow and slurry supply: understand what each does, and get more from your machine.

See how it works ↓
A component being cleaned in a vapour blasting cabinet
WATER + ABRASIVE + COMPRESSED AIR
THE THREE INGREDIENTS Consistent slurry. Suitable pressure. Enough air.
PSI / barAdjust pressure to help control the finish.
CFMSupply enough air for consistent cleaning.
The pumpMix and deliver the abrasive slurry.
01 / HOW IT WORKS

The wet blasting process

Vapour blasting, also called vapor blasting or wet blasting, uses a mixture of water and abrasive media to clean and finish a component. This mixture is called slurry.

01 / Mix and circulate

The pump keeps media suspended in the water and supplies slurry to the blast gun.

02 / Add compressed air

At the gun, compressed air accelerates the slurry through the nozzle towards the component.

03 / Clean and finish

The abrasive acts on the surface. Media, pressure and your technique influence the cleaning action and finish.

04 / Return and repeat

Slurry drains back into the sump for reuse. Keep it maintained, then rinse and dry finished parts appropriately.

02 / HOW IT WORKS

PSI and bar: choose your finish

PSI and bar are two ways of measuring air pressure. Pressure is one of the main adjustments you use to influence the surface finish. These are practical RSM starting points for suitable aluminium parts with an appropriate glass-bead setup.

50–60 PSI
Approximately 3.4–4.1 bar

The satin look

A useful starting range for the even, satin “aerospace-style” appearance many restoration customers want.

20–30 PSI
Approximately 1.4–2.1 bar

A brighter finish

Reducing the pressure can produce a brighter, less matt appearance. Expect a gentler cleaning action and more time on the part.

Start low, test a small area and adjust. These settings are guidance, not a guaranteed finish. Alloy, original surface condition, media type and size, slurry concentration, nozzle distance and technique all matter.

A brighter blasted finish is not the same as mirror polishing. “Aerospace-style” describes an appearance here, not an aerospace process approval or specification.

Check the working pressure while blasting, with air flowing. A high reading when the gun is idle does not prove the compressor can maintain it in use.

03 / HOW IT WORKS

CFM: give the gun enough air

CFM means cubic feet per minute: the volume of air your compressor can deliver. A compressor may reach the required pressure but still struggle to supply enough air continuously.

12–14 CFM

RSM’s suggested minimum delivered airflow for an acceptable cleaning speed on our standard setup. Confirm the requirement for your chosen machine, nozzle and working pressure.

When air supply is limiting performance, more available airflow helps the gun maintain its working pressure and clean consistently. An undersized compressor may run continuously, lose pressure or require you to pause while it catches up.

Look for free air delivery (FAD) at the required pressure, rather than the larger advertised displacement figure. Receiver size gives you a reserve of air; it does not replace adequate continuous output.

A larger compressor gives useful headroom, especially for sustained workshop use. Once the existing gun’s air demand is met, you can take advantage of additional airflow by fitting a larger, correctly matched blast nozzle and air jet. This allows more air through the gun and can increase cleaning capacity, provided the compressor maintains the required working pressure and the slurry supply keeps up.

Extra compressor capacity alone will not increase the airflow through an unchanged gun indefinitely. The nozzle and air jet must be sized together for the machine, with suitable hoses and fittings. Ask us to match the setup to your compressor before changing them.

04 / HOW IT WORKS

Why pump wattage is not the whole story

It is easy to compare machines by the size of their pump motor. But pump wattage on its own is not a measure of blasting power or cleaning speed.

In our air-assisted wet blasting system, the pump’s job is to keep the abrasive mixture circulating and deliver a consistent slurry supply to the gun. The compressed air provides the main acceleration at the gun that projects the slurry onto the component.

Once a suitable pump supplies the gun correctly, fitting a bigger motor does not automatically produce a better finish or faster cleaning. An inadequate compressor can still hold the machine back.

The pump still matters: its design, slurry flow, wear resistance and condition must suit the system. Poor mixing or an inconsistent supply can affect results, even with plenty of compressed air.

Compare the complete pump, gun, nozzle and compressor combination—not just the pump’s wattage.

05 / HOW IT WORKS

A simple way to get started

  1. Check your compressor. Find its delivered airflow at the intended working pressure, and confirm it suits the machine and gun.
  2. Use suitable media and slurry concentration. Follow the machine’s instructions for mixing, maintenance and your intended application.
  3. Start at a lower pressure. Test a small, suitable area before treating the whole component.
  4. Adjust for the result you want. Try the 50–60 PSI satin range or the gentler 20–30 PSI range for a brighter appearance, where appropriate.
  5. Work consistently. Keep the gun moving and control distance and angle. Rinse, dry and inspect the part afterwards.

For cabinet construction, usable space and choosing between machines, read our vapour blasting machine buying guide →

LET’S MATCH YOUR SETUP

Will your compressor
do the job?

Send Max a photo of your compressor’s specification plate and the parts you want to clean. We’ll help you check the air supply and choose a suitable machine.

WhatsApp Max
Your parts.
Your compressor.
Our advice.
Send Max a photo ↗

Optional services are off until you choose them. Change or withdraw your consent here at any time. Your choice is remembered for 180 days.

Read the privacy and cookie notice